All comments:122Replies

  1. balbes150 Elite member 2021-11-25 20:26:54

    Update version 20211124.

    For those who want to build their own version of the kernel\image, sources have been added for self-assembly directly on the p2\m2 device itself.

  2. balbes150 Elite member 2021-11-26 02:53:45

    Images 20211125-edge with  5.16-rc2 kernel for Station P2.

    It works with HDMI, USB (except the upper USB 2.0 port), LAN1, LAN2

    https://disk.yandex.ru/d/gpd4Ayd0Qfpg6A

  3. balbes150 Elite member 2021-11-30 20:11:45

    Image 20211129-edge witch kernel 5.16.rc3
    All USB Wi-Fi and USB sound modules are included. the list of supported file systems and network protocols has been expanded.

  4. chouimat Newbie 2021-12-3 02:57:41

    Are the 5.16.0 sources available?

  5. balbes150 Elite member 2021-12-9 15:01:16

    Ver 20211208-edge kernel 5.16-rc4

  6. blazessdd Newbie 2021-12-11 08:56:15

    Last edited by blazessdd on 2021-12-11 08:58 Editor

    maybe im missing something but:
    i have booted the 4.19 armbian and done sudo /vendor/m2-update..
    then i tried to boot the 5.16 version with no success (just a red blinking light)
    then i installed the 4.19 on the emmc and from there tried to uppdate the bootloader againbut the 5.19 sill not boot
    what am i doing wrong?

    sorry wrong section was menat for m2 ill post this again there...

  7. balbes150 Elite member 2021-12-11 15:01:00

    Last edited by balbes150 on 2021-12-11 15:10 Editor
    blazessdd Posted at 2021-12-11 08:56
    maybe im missing something but:
    i have booted the 4.19 armbian and done sudo /vendor/m2-update..
    the ...

    The correct launch order.
    1. Download, unpack and burn a special update image to the SD card (please note, this is a separate image with a special structure).
    2. Connect the prepared SD card to the device and turn on the power.
    3. Perform the initial setup (answer the questions) and then execute the command     sudo /vendor/p2-station-update-uboot

    4. Download unpack and burn the Armbian image to the SD card.
    5. Connect to the device and turn on the power. If you have done everything correctly, the system will start automatically and in a few minutes there will be an image on the screen. Next, you configure the system as described in the Armbian documentation.

    Please note, items 1-3 are executed once. In the future, they do not need to be performed. This is a one-time operation.


    The 5.16 kernel is experimental and the HDMI output only works with a resolution of 1920x1080 and not on all models TV.

    Important. Use the correct image versions exactly for your model. The image M2 version is different from the P2 version. If you use the wrong version, some of the hardware will not work properly or will not start at all.

  8. blazessdd Newbie 2021-12-11 22:47:08

    Last edited by blazessdd on 2021-12-11 22:51 Editor

    delete message

  9. observer1379 Newbie 2021-12-12 19:41:04

    Last edited by observer1379 on 2021-12-12 19:50 Editor
    balbes150 Posted at 2021-12-11 15:01
    The correct launch order.
    1. Download, unpack and burn a special update image to the SD card (plea ...

    Hi balbes150,
    As a user of station p2, it is so glad to enjoy your great work.
    I'm afraid that I have the same problem just like what blazessdd has met.
    I have followed your steps. From the prompt show on screen, I believe my u-boot has upgraded. However, when I burn latest image, Armbian_21.11.0-trunk_Station-p2_bullseye_edge_5.16.0_xfce_desktop.img.xz , into my sdcard and boot, I stuck at this, and keyboard is not working, I can't input anything.

    I'll flash elder versions of images and try to figure out what stopped the boot progress.
    Once again, appreciate for your great work on so many interesting SBC and tv boxes!


12345678910... 13Next Jump to Page

Reply

You need to log in before you can reply Login | Register